Category Archive for: ‘Tree Shears’


An industry first!  A telescoping Tree Shear.

The TeleClipper is a new innovation from Precision Manufacturing, makers of the HyReach Tree Shear since 1992.  Now you will be able to trim limbs higher than ever before and reach farther into fence rows with the telescoping boom on the TeleClipper.  Land clearing has never been easier.

The telescoping boom extends the cutting surface of the clipper head up to 10’ 3”.  The boom will retract to 7’ 3” for easier and safer transporting and positioning of the clipper prior to cutting.

Customers have asked for more cutting height to make room for equipment along the edges of their fields and right of ways.  Now combines and tractors can operate closer to the fence rows without fear of scratching the paint or breaking costly mirrors or glass.  A longer reach for creek beds and ditches had also been requested.

The TeleClipper also includes a new Extreme Duty cutting head – Model 664000.  The Extreme Duty clipper head has extra-long upper and lower plates resulting in easy release from trees and limbs and at the same time providing additional support for the blades.  The self-cleaning side spacers also reduce the everyday maintenance of the clipper head.

The 180⁰ rotation is an industry first.  Now you can cut close to both sides of the tree without moving the equipment which is a time saving feature.

The cutting, telescoping and 180⁰rotation is controlled from inside the cab with a wireless remote.  Or, if available, use the buttons on your own controls with our pin connectors.

Wireless Troubleshooting

Most problems with the wireless system are battery related.  Make sure the battery in the remote is new.  Make sure the battery in the black metal box is fully charged and will hold its charge – just because the light on the charger turns green does not necessarily mean it is a good battery.  It may not hold its amperage under load.  You will need a battery tester to test this.

When the upper left hand button on the key fob transmitter is pushed you should see a red blinking light.  If light is dim or not flashing rapidly it will need to be replaced.  Follow instructions in manual for replacing the battery.

After you have determined that both the 12v battery and the battery in the key fob/transmitter are fully charged you need to activate or turn on the system.  You can do this by pushing and holding the reset toggle button for 3 to 5 seconds.  The reset toggle button is located on top of the metal box located on the tree shear (older units may have a rubber covered push button).  This will turn on or activate the receiver so it can receive a signal.  Now push the upper left hand button on the key fob/transmitter.  You should hear a clicking noise coming from the valve.  If you hear the clicking noise, your system is operating properly.  Remember the upper left hand button is a momentary switch.  It must remain depressed and held at the same time that you activate your remote hydraulics on your equipment for rotation.

The bottom right button or “OFF” button shuts down the system.  To reactivate the wireless system you will need to push the toggle button again to activate or turn on the system.  Also, the system automatically shuts down after 2 hours of no operation to preserve battery life.

If you did not hear the clicking noise check the fuse located on the wiring harness inside the box.  Next make sure all connections to the battery and to the valve are secure.

If you still do not hear the clicking noise you will need to remove the receiver (unless it is mounted to the back of the metal box where you can clearly see the LED light).  There are two bolts holding the receiver to the side of the black metal box.  Once removed you will need to look for the LED light located by the “L” on the front of the receiver.  When you press and hold the reset button (toggle switch) located on the top of the black metal box, you should see a red blinking LED light in the “L” area of the receiver.  This means the system is turned on and ready to receive a signal.

Next, press and hold the upper left hand button of the key fob remote transmitter.  The red blinking LED light on the receiver should turn solid green.  Release the remote button and the LED light should go back to blinking red.

If the LED light did not turn green, the receiver is not receiving a signal from the key fob transmitter.

You will need to follow the LEARN process found in your owner’s manual.


Brush Management

If you have a problem with trees and brush you likely will need to find equipment that best fits your needs – You can CUT IT or PULL IT and then STACK IT or HAUL IT.

XD7351 Front Loader MountCUT IT

The HyReach Tree Shear allows you to cut at ground level or power rotate the head to trim limbs.

Product 8,2


The Tree Pullers allow you to pull the entire tree out of the ground – roots and all. No stump to interfere.

Product 20


The Pallet Forks allow you to stack material such as hay bales and pallets. Add a grapple to your pallet forks to keep the brush on the forks.

Product 15HAUL IT

You can move the brush to a pile or simply haul it out of your way. There are many grapples to choose from so there is likely one that will fit your needs whether your equipment is large or small. You can even remove rocks with the rock bucket. Add a grapple to the rock bucket to make it even more versatile.



Farm Shows

Farm Shows are starting to wind down after the completion of the National Farm and Machinery Show.  What a show!  Attendance seemed to be normal and the interest in our products seemed better than ever.

Best Selling Tree Shear

The XD Series of Tree Shear is the best selling tree shear by far.

New Commercial Tree Shear

The XD series tree shear has well accepted features:

  • 5/8″ high strength steel on top and bottom frame
  • Extra stabilizer bars and gussets
  • Wireless Remote

XD7351 Front Loader Mount

XD7351 Front Loader Mount

XD6351 Skid Steer Mount

Product 2

To get your XD series tree shear, find a dealer near you.